CON-SERT SCREWS™

Con-Sert Screws were designed to achieve higher pull-out values at
shallower embedments than competitive masonry screws.
The Con-Sert concrete screws replace plastic anchors and sheet
metal screws for lightweight anchoring. Con-Sert Screws eliminate
the need for two piece anchoring. The Con-Sert Screw will cut
threads in a pre-drilled hole in precast, concrete, block, poured
concrete, brick or any other masonry material.
Con-Sert screws are made of heat treated carbon steel with zinc
and yellow dichromate plating.
CON-SERT (GOLD SCREWS) SCREWS® 1/4" (3/4" Embedment) |
Hex Head Item Number |
Flat Head Phillips Item Number |
Box Qty. |
Recommended Embedment |
Size |
14034HS |
14034PS |
100 |
3/4" |
1/4 x 3/4 |
14100HS |
14100PS |
100 |
3/4" |
1/4 x 1 |
14114HS |
14114PS |
100 |
3/4" |
1/4 x 1 1/4 |
14112HS |
14112PS |
100 |
3/4" |
1/4 x 1 1/2 |
14200HS |
14200PS |
100 |
3/4" |
1/4 x 2 |
14214HS |
14214PS |
100 |
3/4" |
1/4 x 2 1/4 |
14212HS |
14212PS |
100 |
3/4" |
1/4 x 2 1/2 |
14300HS |
14300PS |
100 |
3/4" |
1/4 x 3 |
14312HS |
14312PS |
100 |
3/4" |
1/4 x 3 1/2 |
14400HS |
14400PS |
100 |
3/4" |
1/4 x 4 |
14412HS |
14412PS |
100 |
3/4" |
1/4 x 4 1/2 |
Masonry Drill Bit included in each box of 100 screws. All screws have dicromate over zinc plating (3/4" recommended embedment).
CON-SERT (GOLD SCREWS) SCREWS® #8 (1/2" Embedment) |
Hex Head Item Number |
Flat Head Phillips Item Number |
Box Qty. |
Recommended Embedment |
Size |
08012HS |
|
100 |
1/2" |
8 x 1/2 |
08034HS |
08034PS |
100 |
1/2" |
8 x 3/4 |
08100HS |
08100PS |
100 |
1/2" |
8 x 1 |
08114HS |
08114PS |
100 |
1/2" |
8 x 1 1/4 |
08112HS |
08112PS |
100 |
1/2" |
8 x 1 1/2 |
08200HS |
|
100 |
1/2" |
8 x 2 |
Masonry Drill Bit included in each box of 100 screws. All screws have yellow dicromate over zinc plating (1/2" recommended embedment).
1/4" DIAMETER TEST PERFORMANCE DATA |
2000 PSI CONCRETE |
|
4000 PSI CONCRETE |
Tension |
Shear |
|
Tension |
Min.
Embed. |
Max.
Embed. |
Min.
Embed. |
|
Min.
Embed. |
Max.
Embed. |
(3/4") 700 |
(1 1/4") 1000 |
(3/4") 800 |
|
(3/4") 1000 |
(1 1/4") 1650 |
3/4" recommended embedment. Up to 1 1/4" embedment only in extremely soft masonry.
A safety factor of 4:1, or 25% of ultimate, should be used. Critical applications (vibratory
loads, overhead installations) may require a safety factor of as much as 10:1, or more.
Results were based upon drilling the pilot hole with a close tolerance DFS/USA consert drill
bit. To determine screw length needed, add 3/4" to the thickness of the material being
fastened.
*Recommended embedment
#8 TEST PERFORMANCE DATA |
2000 PSI CONCRETE |
|
4000 PSI CONCRETE |
Tension |
Shear |
|
Tension |
Min.
Embed. |
Max.
Embed. |
Min.
Embed. |
|
Min.
Embed. |
Max.
Embed. |
(1/2") 250 |
(3/4") 350 |
(1/2") 650 |
|
(1/2") 500 |
(3/4") 650 |
1/2" recommended embedment. Up to 3/4" embedment only in extremely soft masonry.
A safety factor of 4:1, or 25% of ultimate, should be used. Critical applications (vibratory
loads, overhead installations) may require a safety factor of as much as 10:1, or more.
Results were based upon drilling the pilot hole with a close tolerance DFS/USA consert drill
bit. To determine screw length needed, add 3/4" to the thickness of the material being
fastened.
*Recommended embedment
CON-SERT (GOLD SCREWS) SCREWS® #8 (1/2" Embedment) |
Screw Diameter |
Spacing between
screws center to center |
Minimum
Edged Distance |
#8 |
1 3/4" |
7/8" |
1/4" |
2 5/8" |
1 5/16" |
Anchor spacing recommendations serve only as a guideline. Spacing will vary as the density
of the masonry material changes.
- WILL ELIMINATE AND REPLACE PLASTIC
PLUGS & LEAD ANCHORS
- WILL "TAP THRU" LIGHT STEEL, PLASTIC,
WOOD INTO POURED CONCRETE,
PRECAST, BLOCK AND BRICK MATERIALS
- ALL CON-SERTS ARE CASE HARDENED
WITH ZINC & DICROMATE PLATING
CON-SERTS ARE COMPLETELY
REUSABLE
- CON-SERTS HAVE A SHARP "GIMLET" POINT FOR EASY STARTING
- CON-SERTS ARE AVAILABLE IN:
- 5/16" Slotted Hex Head - 1/4" Diameter
- #3 Flat Head Phillips - 1/4" Diameter
- 1/4" Slotted Hex Head - #8 Diameter
- #2 Flat Head Phillips - #8 Diameter
- CON-SERTS ARE PACKAGED IN:
- 100 Count Open Stock Box with Bit
- Bulk with/without Bits
WHY ONLY A 3/4" EMBEDMENT?
Con-Serts have a uniquely engineered thread
design and drill bit diameter which allows
maximum pullout at minimum embedment.
HOW DOES CON-SERT SAVE MONEY?
HERE'S HOW: In one (100 ct.) box of Con-Sert
Screws drilling at 3/4" embedment you would drill
a total of 6'3" of concrete. Other masonry screws
require a 1 1/4" minimum embedment...and the
same 100 screws would have you drilling 10'5" of
concrete! That's over 4' of extra drilling plus extra
time, extra money and extra bits. A 10 box job
would have you drilling over 40 feet of extra
concrete!
Where do I use Con-Serts? |
• Conduit Straps • Partitions • Joist Hangers • Pipe Run supports • Duct Straps • Gutters • Fuse Boxes • Lighting Fixtures |
• Firring Strips
• 2x2 & 4x4 Wood
• Door Frames
• Wall Hangings
• Light Handles & Rails
• Curtain Rods
• Electrical Boxes
• Window Channels
• Carpet Strips
• Threshold Plates |
 |
 |
Drill hole with Con-Sert I Bit through object and into
concrete.
Use Con-Sert I Tool or (5/16" Hex Driver or #3 Phillips
Driver) to embed screws.
(REMEMBER: Thickness of object + 3/4" = length of screw) |
Drill hole with Con-Sert #8 Bit or 1/8" Masonry Bit through
object and into concrete.
Use Con-Sert #8 Tool or (1/4" Hex Driver or #2 Phillips
Driver) to set screw.
(REMEMBER: Thickness of object + 1/2" = length of screw) |
|