DFS DROP-IN ANCHORS (Made in the USA)
 The DFS Drop-In Anchors were designed
as a replacement for
lead anchors and
lag shields for more satisfactory anchoring
of
objects to concrete and brick.
| DFS DROP-IN ANCHORS - USS |
| Item Number |
Box Qty. |
Description |
| 14100DS |
100 |
1/4" |
| 38196DS |
50 |
3/8" |
| 12200DS |
50 |
1/2" |
| 58238DS |
25 |
5/8" |
| 34300DS |
25 |
3/4" |
| Anchor Size |
Outside Diameter |
Overall Length |
Thread Length |
Min. Embedment |
Drill Size |
*Pull Out |
Box Qty. pcs. |
| 1/4" |
3/8" |
1.2" |
5/8" |
1" |
3/8" |
2273 |
100 |
| 3/8" |
1/2" |
1 5/8" |
5/8" |
1 1/2" |
1/2" |
5520 |
50 |
| 1/2" |
5/8" |
2" |
7/8" |
2" |
5/8" |
7710 |
50 |
| 5/8" |
7/8" |
2 1/2" |
1" |
2 1/2" |
7/8" |
10050 |
25 |
| 3/4" |
1" |
3 1/8" |
1 1/4" |
3 1/8" |
1" |
12010 |
25 |
*Concrete used for testing was 3000PSI. These values cannot be guaranteed due to
variations in concrete. Anchors should be tested in specific material.
A safety factor of 4:1, or 25% of ultimate, should be used. Critical applications (vibratory
loads, overhead installations, etc.) may require a safety factor of as much as 10:1, or more.
| RECOMMENDED SPACING |
Anchor
Diamter |
Embedment |
Spacing
Between Anchors |
Minimum Edge
Distance |
| 1/4" |
1" |
3 1/2 |
1 3/4 |
| 3/8" |
1 5/8" |
5 11/16 |
2 13/16 |
| 1/2" |
2" |
7 |
3 1/2 |
| 5/8" |
2 1/2" |
8 5/16 |
4 1/8 |
| 3/4" |
3 1/8" |
10 1/2 |
5 1/4 |
Anchor spacing recommendations serve only as a guideline. Spacing will vary as the density
of the masonry material changes.
A safety factor of 4:1, or 25% of ultimate, should be used. Critical applications (vibratory loads, overhead installations, etc.) may require a safety factor of as much as 10:1 or more. |
DFS Drop-In Anchors comply with these industry standards:
Meets G.S.A. Standards G.S.A. FF-2-325, Group III, Type 1
Meets load factors in compliance with A.N.S.I. A58. 1
Meets plating standards in compliance with A.S.T.M. B-633
Products tested in accordance with A.S.T.M. E-488.88
What advantages are there?
DFS Drop-In Anchors have a much smaller hole
diameter requirement than lead anchors.
The DFS Drop-In Anchors have much greater
pull-out strength than lead anchors and lag
shields.
DFS Drop-In Anchors are preassembled. Ready
for use right out of the box! |
- FOR FLUSH & SHALLOW EMBEDMENT
ANCHORING TO POURED CONCRETE
AND BRICK MATERIALS
- FOR USE WITH ANY LENGTH USS
COARSE BOLT OR THREADED ROD
CARBON STEEL BODY AND SETTING
PLUG
- ALSO AVAILABLE WITH RICHMOND
THREAD FOR REBAR REINFORCEMENT
- ZINC PLATED FOR CORROSION
RESISTANCE
- AVAILABLE WITH OR WITHOUT DROP-IN
SETTING TOOLS
- AVAILABLE IN OPEN STOCK BOXES OR BULK
|
Installation Procedure
Where do I use DFS Drop-In Anchors? |
- Temporary Machinery Anchoring
- Overhead Hangers with Threaded Rod
- Railings, Guard Rails and Hand Rails
- Shelving and Brackets
- Anchoring Rack Systems
|
- Lighting Fixtures
- Gates and Fencing
- 4 x 4 Wood Anchoring
- Rebar to Old, Existing Masonry Floors
- Other Shallow or Flush Embedment Anchoring
|
|
